Installation Instructions
Everything you need to install decals perfectly.
Any queries or questions about installation, contact out team and we'll get back to you as soon as possible.
Fork Decal Application Instructions
Fork Decal Application
*Read Instructions Very Carefully and follow each step
Left Side
1: Remove old decals. Hairdryer or heat gun on (warm not hot) setting can be helpful but not necessary.
2: Remove sticky residue from fork lowers, and clean thoroughly.
3: Place decals on the forks to line them up and make sure they fit correctly. (Without removing backing just yet)
4: Peel half of the backing paper off (from the right side) and cut that half of the backing paper off.
5: Line up the decal once again (making sure not to stick it down just yet) making sure everything lines up and is straight.
6: With a credit card or hard plastic card gently start to apply pressure on the side that is exposed, working from the left side to the right, making sure everything is stuck down nicely. Using one hand to hold the other side of the decal still.
7: Once one-half side has been stuck down, grab the other half of the backing paper and start to slowly peel that away, whilst slowly scraping it right to left (with the card) until all the backing is removed and the sticker is applied fully.
8: Scrape the decal thoroughly (not too hard but enough to make it stick well) side to side slowly getting rid of any bubbles is they are present. (Bubbles shouldn’t necessarily appear using this technique correctly).
9: Slowly start peeling away the clear film from a corner, making sure everything is sticking to the forks. If not lay the clear sheet back down just to the part that isn’t sticking, to the point where it is on the fork. Once on the fork again, scrape or rub the piece that isn’t sticking a few times. When you can continue on with peeling the clear layer and it is sticking you have done it correctly.
10: When all of the clear layer has been peeled off, you have successfully applied a fork decal.
Right Side
Repeat the steps for the left side except for the direction of scraping, instead of scraping right to left scrape left to right, and instead of scraping left to right, scrape right to left etc..
Tips:
Lay the new decal over the old one and line it up and mark it with masking tape to try and get an accurate/aligned decal. *Not all decals are the same size as the stock ones that come on forks.
Rear Shock Decal Application Instructions
Shock Decal Application
*Read Instructions Very Carefully and follow each step
1: Remove old decals. Hairdryer or heat gun on (warm not hot) setting can be helpful but not necessary.
2: Remove sticky residue from shock, and clean thoroughly.
3: Place decals on the shock to line them up and make sure they fit correctly. (Without removing backing just yet)
4: Peel half of the backing paper off (from the right side).
5: Line up the decal once again (making sure not to stick it down just yet) making sure everything lines up and is straight.
6: With a credit card or hard plastic card/ fingers or hand gently start to apply pressure on the side that is exposed, working sideways left to right or right to left (whichever is preferred) making sure everything is stuck down nicely. Using one hand to hold the other side of the decal still.
7: Once one-half side has been stuck down, continue to slowly peel the rest of the backing away, whilst slowly scraping it right to left/ left to right (with the card/hand or fingers) until all the backing is removed and the sticker is applied fully.
8: Scrape the decal thoroughly (not too hard but enough to make it stick well) side to side slowly getting rid of any bubbles is they are present. (Bubbles shouldn’t necessarily appear using this technique correctly).
9: Slowly start peeling away the clear film from a corner, making sure everything is sticking to the shock. If not lay the clear sheet back down just to the part that isn’t sticking, to the point where it is on the shock. Once on the shock again, scrape or rub the piece that isn’t sticking a few times. When you can continue on with peeling the clear layer and it is sticking you have done it correctly.
10: When all of the clear layer has been peeled off, you have successfully applied a fork decal.
*Not all decals are the same size as the stock ones that come on shocks, sizes may vary
Sticker Application Instructions
Instructions on how to apply.
Step 1: Clean the surface you’re going to apply your sticker to thoroughly and let dry completely
Step 2: Peel off tape being careful that the sticker comes off with it.
Step 3: Apply the tape and sticker to the surface and rub the sticker thoroughly.
Step 4: Peel the tape off delicately making sure the sticker stays on the surface. If not try and rub the sticker in the spot where it is not sticking. If it is still not sticking, try and peel the tape off from another direction.
Step 5: When tape is completely peeled off give the sticker another rub just to make sure it’s stuck down. You now have a fully applied sticker.